Best Greenhouse Plastic for Saudi Arabia: Heat, UV, Diffusion & Cooling Guide

Choosing the best greenhouse plastic for Saudi Arabia is very different from choosing greenhouse film for a mild European climate.

Saudi greenhouse projects must deal with a combination of:

• Very high summer temperatures

• Strong solar radiation

• Long periods of intense sunlight

• Low rainfall in most regions

• Water scarcity

• Large day/night temperature differences in some inland areas

• Higher humidity in some coastal locations

• Dust and sand

• High greenhouse cooling demand

Saudi Arabia’s National Center for Meteorology describes the country as mainly semi-arid to arid desert, with typical maximum temperatures of approximately 35–45°C during summer, while also noting important differences between coastal and inland regions.

For many Saudi commercial greenhouse projects, a practical starting point is therefore:

UV-stabilized PE or PO greenhouse plastic + high usable light transmission + suitable light diffusion + appropriate mechanical strength

with functions such as:

Anti-Fog / Anti-Drip / IR / EVA

added only when the location and production system actually require them.

There is no single greenhouse film specification that is best for all of Saudi Arabia.

A greenhouse in Riyadh, a coastal project in the Eastern Region and a cooler highland or winter-production greenhouse may require very different film properties.

Quick Recommendation: Greenhouse Film for Saudi Arabia

The final specification should always be matched to the greenhouse structure, crop and local climate.

Why Saudi Arabia Needs Special Greenhouse Plastic

Saudi Arabia is investing heavily in protected agriculture and controlled-environment production as part of its strategy to increase agricultural efficiency and food security.

The Saudi Ministry of Environment, Water and Agriculture identifies protected agriculture and environmental control systems as an important agricultural technology area. Its technology roadmap also notes a national aim of producing 3.4 million tons of vegetables by 2030 and cites studies suggesting protected agriculture can reduce water use in vegetable production by roughly 20–25%.

This makes greenhouse technology especially relevant in a country where water efficiency and extreme climate management are major concerns.

But the greenhouse covering itself has to be designed for that environment.

A basic greenhouse plastic developed for moderate weather may not be the best choice for:

45°C summer conditions + intense sunlight + desert exposure.

The Main Challenge Is Not Just Heat

When buyers say:

“Saudi Arabia is hot, so I need heat-resistant greenhouse plastic.”

the issue is more complicated.

Saudi greenhouse film may need to manage several stresses at the same time:

1. UV Exposure

Strong sunlight can accelerate polymer degradation.

2. Solar Heat Load

Too much direct radiation can increase crop and greenhouse temperature.

3. Water Efficiency

Cooling strategy affects water and energy consumption.

4. Dust

Dust accumulation can reduce optical performance.

5. Wind

Exposed greenhouse structures need appropriate mechanical performance and installation.

6. Condensation

Even desert greenhouses can experience internal condensation.

7. Nighttime Temperature

Some inland or cooler areas may experience substantial day/night temperature differences.

This is why a Saudi greenhouse film should be designed as a complete specification rather than simply ordered as:

“200 micron UV plastic.”

What Thickness of Greenhouse Plastic Is Best for Saudi Arabia?

For commercial projects, buyers commonly evaluate film in the range of approximately:

150–200 micron

depending on the greenhouse structure and required mechanical performance.

Thickness should not be considered independently from:

• UV stabilization

• Tensile properties

• Elongation

• Structure design

• Wind exposure

• Installation method

• Required service life

150 Micron Greenhouse Film for Saudi Arabia

150 micron can be attractive where:

• Cost per square meter matters

• Greenhouse structures are properly designed

• Wind conditions are manageable

• Buyers want more covered area per ton

• The formulation has suitable UV stabilization

It can be a practical commercial greenhouse-film thickness.

However, it should not automatically be selected for every structure.

180 Micron Greenhouse Film

180 micron can provide a middle position between 150 and 200 micron.

It may appeal to customers who want additional material and mechanical margin without moving fully to 200 micron.

Whether distributors should stock it depends on local market demand.

200 Micron Greenhouse Film for Saudi Arabia

200 micron is often attractive for:

• Large commercial greenhouse structures

• Heavy-duty applications

• More demanding installations

• Buyers accustomed to thicker greenhouse covering

It contains approximately 33% more material per square meter than 150 micron, assuming similar density and formulation.

However:

200 micron does not automatically mean better UV resistance.

A properly formulated 150 micron film may perform better outdoors than a poorly stabilized 200 micron film.

UV Stabilization Is One of the Most Important Specifications in Saudi Arabia

Saudi greenhouse plastic is exposed to strong solar radiation for long periods.

Without an appropriate stabilization system, polymer degradation may cause the film to:

• Become brittle

• Lose elongation

• Lose mechanical strength

• Crack

• Tear prematurely

• Change optical properties

Therefore, a Saudi buyer should not ask only:

“How thick is the film?”

They should also ask:

“What climate and service-life target is the UV stabilization system designed for?”

2-Year, 3-Year or 5-Year Greenhouse Film?

Greenhouse plastic may be formulated for different intended service-life targets.

Examples include:

• 2 years

• 3 years

• 5 years

But these numbers should not be treated as unconditional guarantees.

Actual service life can be influenced by:

• Solar radiation

• Temperature

• Agricultural chemicals

• Wind

• Installation

• Greenhouse structure

• Film formulation

Saudi Arabia is exactly the kind of market where a generic “5-year film” claim should be examined carefully.

The buyer should tell the manufacturer:

Saudi Arabia + exact region + greenhouse type + crop + chemical-use conditions

before confirming the film.

UV Stabilization vs UV Blocking in Saudi Arabia

These are different properties.

UV Stabilization

Protects the plastic from UV-induced degradation.

UV Blocking

Controls how much selected ultraviolet radiation passes through the greenhouse covering.

For most Saudi projects, strong UV stabilization is fundamental.

Special UV blocking is a separate decision.

Do not assume:

more UV blocking = better greenhouse film.

UV transmission can influence crops, insects and pollination.

Strong UV Protection Does Not Mean Dark Film

Some buyers assume strong UV resistance requires lower light transmission.

That is incorrect.

A film can be designed for:

strong outdoor UV durability

while still maintaining:

high useful visible-light transmission.

These should be treated as separate technical targets.

Is Clear Greenhouse Plastic Best for Saudi Arabia?

Not always.

Completely clear greenhouse film allows a high proportion of incoming solar radiation to continue in its original direction.

Under strong Saudi sunlight, this can create:

• Strong direct radiation on upper leaves

• Hot crop surfaces

• Uneven canopy illumination

• Higher localized heat loads

For many commercial vegetable greenhouses, some level of light diffusion may be preferable.

Why Diffused Greenhouse Film Is Important in Saudi Arabia

Diffusion scatters incoming sunlight into multiple directions.

This can help distribute light more evenly through the greenhouse and crop canopy.

For crops such as:

• Tomatoes

• Cucumbers

• Peppers

diffused light may improve canopy-level light distribution compared with highly directional sunlight.

In strong-sunlight environments, this can be particularly useful.

High Diffusion Does Not Mean Low Light

This distinction is important.

A good diffused greenhouse film aims to achieve:

High Useful Light Transmission + Effective Diffusion

rather than simply making the greenhouse darker.

Diffusion and shading are not the same thing.

Diffusion vs Shading in Saudi Greenhouses

Diffusion

Changes the direction of incoming light.

Shading

Reduces the total amount of solar radiation entering.

These serve different functions.

A high-diffusion greenhouse film may distribute sunlight more evenly, but it cannot replace:

• Shade screens

• Whitewash

• Cooling systems

• Ventilation

when solar heat load becomes excessive.

Can Greenhouse Plastic Keep a Saudi Greenhouse Cool?

Only partially.

No plastic film can independently solve extreme greenhouse heat.

In Saudi summer conditions, temperature control may require a system combining:

Film + Ventilation + Shading + Evaporative Cooling + Climate Control

depending on project sophistication.

Saudi Arabia’s protected-agriculture strategy specifically emphasizes environmental-control technologies because operating a greenhouse in the Kingdom’s hot climate requires active management of temperature and humidity.

The film is one component of that system.

Do Not Expect “Cooling Film” to Replace Greenhouse Cooling

Terms such as:

• Heat-reduction film

• Cooling greenhouse film

• IR-blocking film

• NIR film

should be evaluated carefully.

A specialized film may modify part of the solar spectrum.

But in very hot Saudi conditions, cooling capacity still depends heavily on:

• Air exchange

• Evaporative cooling

• Fan-and-pad systems

• Shading

• Greenhouse design

A film alone cannot maintain ideal crop temperatures during extreme summer heat.

Solar IR Blocking vs Thermal IR Film

This is one of the most important distinctions for Saudi buyers.

Solar IR / NIR Management

Designed to reduce or modify part of incoming solar near-infrared energy.

Possible objective:

reduce daytime heat load

Thermic IR Film

Designed to reduce outgoing long-wave infrared radiation.

Possible objective:

retain nighttime heat

These are almost opposite thermal objectives.

A supplier should clearly explain which type is being quoted.

Does Saudi Arabia Need IR Thermic Film?

Not everywhere.

For many hot locations, retaining more heat at night may not be the main objective.

In those projects, thermic IR may provide limited value.

However, IR may be useful in:

• Winter production

• Northern areas

• Cooler inland nights

• Higher elevations

• Temperature-sensitive crops

The decision should be based on actual nighttime temperature.

Riyadh Greenhouse Film: What Should Buyers Prioritize?

Riyadh and many central inland areas are characterized by dry desert conditions and strong temperature variation.

The Saudi meteorological service describes the national climate as hot and arid, with notable differences between daytime and nighttime conditions, while current agricultural policy also identifies greenhouse vegetable production in parts of the Riyadh region.

For many central Saudi greenhouse projects, priorities may include:

Strong UV Stabilization + High Transmission + Medium/High Diffusion + Appropriate Mechanical Strength

AF can still be included because humidity inside the greenhouse can be much higher than outdoor humidity.

Why Anti-Fog Can Still Matter in Dry Riyadh

Outside air may be dry.

Inside the greenhouse, conditions are different.

Water enters the internal environment through:

• Irrigation

• Plant transpiration

• Hydroponic systems

• Evaporative cooling

When humid internal air contacts a cooler film surface, condensation may form.

Therefore:

dry desert climate does not mean zero greenhouse condensation.

AF can still be valuable.

Eastern Region Greenhouse Film

The Eastern Region requires a different approach.

Saudi Arabia’s meteorological data shows a clear climatic difference between inland and coastal areas, and coastal locations can experience much higher humidity than central desert environments.

For hot, more humid eastern projects, useful priorities can include:

Strong UV + Diffusion + Anti-Fog + Anti-Drip

with careful attention to ventilation.

Heat plus humidity can make greenhouse climate management particularly demanding.

Anti-Fog Film for Humid Saudi Greenhouses

AF technology helps modify how condensation behaves on the inner film surface.

Instead of forming many individual droplets, condensed water is encouraged to spread more evenly.

Potential benefits include:

• Better optical clarity during condensation

• Reduced droplet formation

• Better water behavior on the inner surface

AF does not remove humidity.

It works together with greenhouse climate management.

Anti-Fog vs Anti-Drip

These terms are related but not identical.

Anti-Fog

Primarily addresses small condensation droplets that create a fog-like appearance.

Anti-Drip

Focuses on reducing large droplets that may fall onto the crop.

For humid greenhouse environments, both can be useful.

Greenhouse Film for Saudi Tomato Production

Commercial tomato production is one of the important applications for controlled-environment agriculture in Saudi Arabia, and modern hydroponic tomato greenhouse projects are already operating in the Kingdom.

For many Saudi tomato greenhouses, a useful starting specification is:

150–200 micron PO or PE + Strong UV + Suitable Diffusion + AF

Other functions should depend on the specific region.

Why Tomato Greenhouses Benefit From Diffusion

Commercial tomato crops often develop tall, dense canopies.

Under strong direct sunlight, the upper canopy may receive much more radiation than lower leaves.

Diffused light can help distribute radiation more evenly.

This makes diffusion particularly relevant in high-solar-radiation regions.

However, the correct diffusion level must still preserve high usable light.

Best Greenhouse Film for Cucumbers in Saudi Arabia

Cucumbers create a different microclimate.

Dense foliage and high transpiration can contribute to high internal humidity.

A useful Saudi cucumber film may combine:

Strong UV + Diffusion + AF + Anti-Drip

with thickness selected according to greenhouse structure.

In consistently hot regions, thermic IR may not be necessary.

Best Greenhouse Film for Bell Peppers in Saudi Arabia

Pepper and bell-pepper production can be sensitive to strong direct sunlight and high fruit-surface temperature.

A diffused greenhouse film may help distribute light more evenly.

A practical starting specification can be:

UV + Medium/High Diffusion + AF

with appropriate thickness and mechanical properties.

Greenhouse Film for Hydroponic Projects

Hydroponics and protected agriculture are increasingly important in Saudi agricultural development because they allow greater control over the root environment, water and crop production.

Saudi government technology planning explicitly includes hydroponics, soilless cultivation and controlled-environment systems within protected agriculture.

For hydroponic greenhouse projects, film selection should consider:

• Transmission

• Diffusion

• Heat load

• Condensation

• Cooling strategy

• Crop

• Year-round operating schedule

The film should be selected as part of the entire climate-control system.

Why Water Efficiency Matters in Saudi Greenhouses

Water scarcity is one of the defining agricultural challenges in Saudi Arabia.

The Ministry’s National Water Strategy notes the heavy dependence of agriculture on non-renewable water resources, while Saudi agricultural policy emphasizes improved irrigation efficiency and protected production.

This matters for greenhouse-film selection because excessive solar heat can increase:

• Cooling demand

• Evaporative water use

• Crop stress

The film should therefore support—not work against—the greenhouse’s overall climate and water-management strategy.

Should Saudi Greenhouse Film Be Highly Diffused?

Often, medium or high diffusion deserves serious consideration.

But there is no universal percentage that is best for Saudi Arabia.

The correct balance depends on:

• Crop

• Greenhouse geometry

• Growing season

• Light transmission

• Shading system

• Cooling system

A film with very high diffusion but poor overall transmission may not be ideal.

Ask for both:

Light Transmission %

and:

Diffusion %

when comparing suppliers.

What About Full-Diffusion PO Greenhouse Film?

Full-diffusion PO film can be attractive for high-value vegetable production in strong-sunlight regions.

It may provide:

• More even light distribution

• Reduced direct hot spots

• Better canopy penetration

But it should still be evaluated together with:

• Total transmission

• Crop

• Cooling system

• Greenhouse structure

“Full diffusion” should not be treated as a universal answer.

Dust Is an Important Saudi Greenhouse Issue

Dust can accumulate on greenhouse coverings and reduce incoming light.

In desert environments, film optical performance is therefore affected by both:

the original film properties

and:

surface cleanliness during use.

Regular cleaning may become part of greenhouse management.

Does “Self-Cleaning Greenhouse Film” Work?

Some films are marketed with improved surface-cleaning properties.

Buyers should be cautious with exaggerated claims.

Dust accumulation depends on:

• Surface properties

• Rainfall

• Wind

• Static behavior

• Dust composition

• Cleaning frequency

A film may improve surface behavior, but it cannot guarantee a permanently clean greenhouse in desert conditions.

Can Cleaning Damage Greenhouse Film?

Potentially.

Aggressive brushes, abrasive materials or strong chemicals can affect the film surface.

Follow manufacturer cleaning recommendations.

This is especially important for films with functional inner or outer layers.

Agricultural Chemicals and Saudi Greenhouse Film

Crop-protection programs may involve chemicals that affect greenhouse film stabilizers.

Potential concerns include repeated exposure to compounds containing:

• Sulfur

• Chlorine

The actual risk depends on concentration and formulation.

Buyers should tell the manufacturer about intensive sulfur or chlorine use before production.

Chemical exposure may also affect warranty conditions.

What Color Should Saudi Greenhouse Plastic Be?

For most commercial vegetable greenhouse projects, a clear or optically designed translucent film is more appropriate than simply selecting a colored plastic.

Color should never replace technical optical data.

Ask for:

• Light transmission

• Diffusion

• UV properties

• IR properties

rather than choosing based on visual appearance alone.

PO vs PE Greenhouse Film for Saudi Arabia

Both can work.

PE Greenhouse Film

PE-based greenhouse film can be:

• UV stabilized

• Diffused

• Anti-fog

• Anti-drip

• Thermally modified

It can provide a cost-effective commercial solution.

Commercial PO Film

“PO greenhouse film” is commonly used as a commercial term for more highly functionalized multilayer polyolefin greenhouse film.

It may combine:

• UV

• Diffusion

• AF

• IR

• EVA

• Multiple functional layers

But the label PO does not automatically guarantee superior performance.

Compare technical specifications.

Is PO Better Than PE in Saudi Arabia?

Not automatically.

A high-quality PE greenhouse film with the correct Saudi-climate formulation may be better than a poorly formulated PO product.

The important questions are:

• What UV stabilization system is used?

• What is the intended lifetime?

• What is the light transmission?

• What is the diffusion?

• Does AF last long enough?

• What are the mechanical properties?

• Is the film suited to the local climate?

Does EVA Make Sense for Saudi Arabia?

Sometimes.

EVA can influence:

• Flexibility

• Low-temperature behavior

• Thermal characteristics

• Optical properties

But EVA should not be added simply because customers think:

more EVA = better film.

For very hot Saudi projects, the manufacturer should explain exactly what benefit the EVA formulation is intended to provide.

EVA Is Not the Same as IR

This is important.

EVA ≠ IR

and:

EVA ≠ AF

and:

EVA ≠ UV stabilization

These functions may be combined, but they are separate technical concepts.

5-Layer vs 7-Layer Greenhouse Film

A multilayer co-extrusion structure allows manufacturers to distribute different functions across the film.

For example:

Outer Layers

May focus on:

• UV durability

• Weather resistance

Middle Layers

May contribute:

• Mechanical properties

• Diffusion

• IR functions

Inner Layer

May focus on:

• AF

• Anti-drip

A 7-layer film provides greater formulation flexibility.

However:

More layers do not automatically mean better quality.

The actual formulation matters more.

Best Film for Large Saudi Commercial Greenhouses

Large controlled-environment projects should evaluate film more professionally than small tunnel projects.

Key data can include:

• Thickness tolerance

• Light transmission

• Diffusion

• UV stabilization

• Thermal properties

• AF duration

• Tensile strength

• Elongation

• Chemical resistance

• Installation orientation

For high-value projects, requesting technical data is more useful than comparing only price per kilogram.

Greenhouse Film Widths for Saudi Arabia

Commercial greenhouse projects may require a wide range of covering widths depending on structure.

Widths may include:

• 6 m

• 8 m

• 10 m

• 12 m

• 14 m

• 16 m

• 18 m

• 20 m

GH Agricultural Film can manufacture greenhouse film up to 20 meters wide.

However, the widest film is not automatically the best film.

The correct width depends on the greenhouse structure.

Greenhouse Width Is Not Film Width

An 8-meter greenhouse does not automatically require an 8-meter film.

Film must cover:

• Roof curvature

• Side portions

• Fixing area

• Installation allowance

Always measure the actual covering distance.

Greenhouse Film Weight Example

Using approximately 0.92 g/cm³ as a theoretical PE-based density:

Weight (kg) ≈ Width × Length × Thickness × 0.00092

For example:

12 m × 100 m × 200 micron

≈ 220.8 kg

before core and packaging.

This matters for Saudi distributors because very large rolls may require forklifts or lifting equipment.

How Much Greenhouse Film Fits in a 40HQ Container?

For planning purposes, a 40HQ shipment of greenhouse film may often be around:

25–26.5 metric tons

depending on:

• Container payload

• Route

• Packaging

• Pallets

• Regulations

Buyers should confirm actual allowable loading for every shipment.

Approximate Square Meters per Ton

Using theoretical density of approximately 0.92 g/cm³:

This is useful for Saudi distributors comparing:

cost per kg vs cost per m².

Do Saudi Distributors Need 200 Micron Only?

No.

A distributor may benefit from offering different product levels.

For example:

Commercial Series

150 micron UV + Diffusion

Heavy-Duty Series

200 micron UV + Diffusion

Premium Vegetable Series

PO + Strong UV + High Diffusion + AF

Humid-Climate Series

PO + UV + Diffusion + AF + Anti-Drip

Winter / Cooler-Area Series

UV + High Transmission + IR / EVA where needed

The exact range should follow actual local demand.

Suggested Saudi Distributor Product Matrix

This should be treated as a starting framework, not a fixed Saudi standard.

What Greenhouse Functions Should Saudi Buyers Prioritize?

A practical priority order is often:

Priority 1 — UV Stabilization

Essential for outdoor durability.

Priority 2 — Light Transmission

Crops still need usable light.

Priority 3 — Diffusion

Especially valuable under strong direct sunlight.

Priority 4 — Mechanical Performance

Important for structure reliability and installation.

Priority 5 — Anti-Fog / Anti-Drip

More important in humid or high-transpiration environments.

Priority 6 — IR / EVA

Add only where climate and season justify them.

This avoids paying for unnecessary functions.

Common Mistakes When Buying Greenhouse Plastic for Saudi Arabia

Mistake 1: Choosing Only by Thickness

200 micron does not guarantee better UV durability.

Mistake 2: Buying the Film With the Most Additives

More functions do not automatically mean a better product.

Mistake 3: Confusing Diffusion With Shading

Diffusion redistributes light; shading reduces radiation.

Mistake 4: Assuming IR Always Means Cooling

Thermic IR may actually be designed to retain heat.

Mistake 5: Ignoring Internal Humidity

Even desert greenhouses can develop condensation.

Mistake 6: Ignoring Dust

Optical performance can decline when the outer film becomes dirty.

Mistake 7: Ignoring Agricultural Chemicals

Sulfur and chlorine exposure may affect some film systems.

Mistake 8: Comparing Only USD/kg

Compare specification and cost per square meter.

Mistake 9: Expecting Film to Replace Cooling Equipment

Extreme summer greenhouse climate requires system-level design.

Mistake 10: Using One Film for Every Saudi Region

Coastal, inland, northern and higher-altitude projects can have different requirements.

How to Compare Greenhouse Film Quotations in Saudi Arabia

Ask every supplier to quote the same specification.

Only then is the price comparison meaningful.

Questions Saudi Buyers Should Ask a Greenhouse Film Manufacturer

Before ordering, ask:

1. Is the film designed for high-temperature, high-UV climates?

2. What service-life target is recommended for Saudi Arabia?

3. What is the light transmission?

4. What is the diffusion?

5. Is AF included?

6. Is anti-drip included?

7. Does IR mean thermal retention or solar heat reduction?

8. Is EVA included?

9. What mechanical properties are available?

10. What chemicals can affect the film?

11. What installation direction is required?

12. What thickness tolerance is used?

13. What widths can be produced?

14. Can packaging be customized?

15. What is the MOQ per specification?

These questions reveal much more than asking:

“What is your 200 micron PO price?”

Recommended Starting Specifications by Saudi Application

These are starting points only.

The exact formulation should be selected after reviewing the project.

What Information Should a Saudi Buyer Send for a Quotation?

Provide:

The more accurate the project information, the better the film recommendation.

Frequently Asked Questions

What is the best greenhouse plastic for Saudi Arabia?

For many commercial vegetable projects, a good starting point is 150–200 micron UV-stabilized PE or PO greenhouse film with high useful light transmission, suitable diffusion and AF where required.

The final specification depends on region, crop and cooling system.

Is 200 micron greenhouse film best for Saudi Arabia?

Not always.

200 micron provides more material and may suit heavy-duty structures, but UV stabilization and formulation are equally important.

What greenhouse plastic is best for Riyadh?

Strong UV stabilization, good light transmission, suitable diffusion and adequate mechanical performance should usually be priorities.

AF may also be valuable despite the dry outdoor climate.

Is high-diffusion film good for Saudi Arabia?

It can be very useful in strong-sunlight environments, especially for commercial vegetable crops.

However, diffusion should be balanced with high light transmission.

Does Saudi greenhouse plastic need anti-fog?

Often, yes.

Greenhouses can become humid internally because of irrigation, transpiration and cooling systems even when outside air is dry.

Does Saudi Arabia need IR greenhouse film?

Not every project.

Thermic IR is more useful where nighttime heat retention matters.

It may be unnecessary in consistently warm locations.

Is IR film a cooling film?

Not necessarily.

Thermic IR film normally reduces long-wave nighttime heat loss.

Solar NIR-management film is a different technology.

What greenhouse film is best for tomatoes in Saudi Arabia?

A useful starting specification is:

UV + Diffusion + AF

with thickness selected according to the greenhouse structure.

What greenhouse film is best for cucumbers in Saudi Arabia?

A common starting point is:

UV + Diffusion + AF + Anti-Drip

because cucumber greenhouses can have high humidity.

Is PO greenhouse film better than PE for Saudi Arabia?

Not automatically.

The actual UV, optical, mechanical and functional specification matters more than the name PO or PE.

Can Saudi greenhouse distributors use private-label film?

Yes.

Thickness, widths, functions, packaging and branding can all be customized depending on production requirements.

Greenhouse Film Manufacturer for Saudi Arabia

GH Agricultural Film manufactures customized greenhouse covering for Saudi agricultural distributors, greenhouse contractors and commercial growers.

Our greenhouse-film range includes:

• PO greenhouse film

• PE greenhouse film

• EVA greenhouse film

• High-diffusion greenhouse film

• Anti-fog greenhouse film

• Anti-drip greenhouse film

• IR greenhouse film

• Multi-functional greenhouse film

Our production capabilities include 7-layer co-extrusion technology.

Greenhouse film can be customized according to:

• Thickness

• Width

• Length

• UV service life

• Light transmission

• Diffusion

• AF

• Anti-drip

• IR

• EVA

• OEM packaging

• Private-label branding

Maximum film width can reach 20 meters.

For Saudi projects, we recommend selecting the specification according to:

Region + Crop + Greenhouse Structure + Growing Season + Cooling System + Required Service Life

rather than using one universal film formulation.

Request a Greenhouse Film Recommendation for Saudi Arabia

To receive a more suitable quotation, provide:

Saudi Region
Crop
Greenhouse Type
Growing Season
Thickness
Width & Length
Required Service Life
Cooling System
Required Film Functions
Quantity
Destination Port

This information allows the greenhouse film formulation to be matched more closely to the actual Saudi growing environment.